Menu

All products from zander at a glance!

Adsorptionstrockner Kaltregeneration
Hersteller: Zander
Zander CDAS - CLEAN DRY AIR SYSTEM
  • New Series
Fully automatic heatless regenerating adsorption dryer.
Volume flow 55 m³/h to 300 m³/h
  • EST - energy saving technology
  • Big screen with lots of real time information
  • High strength desiccant
The cartridges are used in blizzard with
high strength desiccant filled with a life of
5 years for aconsistent drying, regeneration and dew point temperature ensures.
  • Pre assembled filters
The new filters in the OIL-X series offer performance certified to ISO 8573-1
Validation according to ISO 12500
  • Screwed lid
The bolted lid allows easy replacement of the desiccant cartridge.
  • Adjustable flushing pressure
The purging air can be easily adjusted to the minimum operating pressure without special tools.
  • Corrosion resistant column
With 10 years warranty to ensure a long service life.
  • Internal flow paths with full passage
With optimized flow management to reduce pressure drop.
  • Cylinder valve system with full passage
Valves with low pressure loss ensure an unimpeded air flow and low back
pressure, while rugged cylinders extend service intervals.
  • Base plate designed for pallet trucks
Enables a simple, time saving installation.
Alternatively with oil vapor adsorber (OFAS series)
Adsorptionstrockner Kaltregeneration
Hersteller: Zander
Zander OFAS - OIL FREE AIR SYSTEM
  • New Series
Fully automatic heatless regenerating adsorption dryer with oil vapor removal
Volume flow 55 m³/h to 300 m³/h
  • EST - energy saving technology
  • Big screen with lots of real time information
  • High strength desiccant
The cartridges are used in blizzard with
high strength desiccant filled with a life of
5 years for aconsistent drying, regeneration and dew point temperature ensures.
  • Pre assembled filters
The new filters in the OIL-X series offer performance certified to ISO 8573-1
Validation according to ISO 12500
  • Screwed lid
The bolted lid allows easy replacement of the desiccant cartridge.
  • Adjustable flushing pressure
The purging air can be easily adjusted to the minimum operating pressure without special tools.
  • Corrosion resistant column
With 10 years warranty to ensure a long service life.
  • Internal flow paths with full passage
With optimized flow management to reduce pressure drop.
  • Cylinder valve system with full passage
Valves with low pressure loss ensure an unimpeded air flow and low back
pressure, while rugged cylinders extend service intervals.
  • Base plate designed for pallet trucks
Enables a simple, time saving installation.
Adsorptionstrockner Kaltregeneration
Hersteller: Zander
Zander KA-MT - Generation 2
  • Fully automatic heatless regenerating adsorption dryer with oil vapor removal
  • Volume flow from 8 m³/h to 940 m³/h
  • Efficient up to a pressure dew point of -70 ° C
  • Cleaning up to residual oil contents of 0.003 mg / m³
  • Flow rates up to 940 m³ / h (suction capacity of the compressor when compressed to 7 bar)
  • Compressed air can be dried according to pressure dew point from -25 ° C to -70 ° C
  • Ready to use preparation unit with activated carbon stage including prefilter and dustfilter
  • heatless regenerated, with multitronic plus control
  • Optionally with dew point control
  • Mains voltage 230 V, 50-60 Hz
  • Residual oil content up to 0.003 mg / m³
Downloads
Adsorptionstrockner Kaltregeneration
Hersteller: Zander
Zander KE(A)-MT
  • Heatless regenerating adsorption dryers for volume flows from 1200 to 6100 m³ / h
  • Stainless steel sieve plates on the wet side
  • High quality desiccant
  • Separately controlled main and blow-off valves
  • Generously dimensioned and tight-fitting non-return valves.
Adsorptionstrockner Warmregeneration
Hersteller: Zander
Zander WVM
  • Adsorption dryer, heat regenerated
  • Volume flow 1500 m³/h to 14500 m³/h (other sizes on request)
  • Fully automatic adsorption dryer with vacuum regeneration for drying compressed air
  • Warm regeneration without purging air
  • Dew point control incl.
  • Zander Dryer Memory Control (ZDMC)
  • Low Energy System
  • Two-layer filling
  • Active heating in the vacuum range
  • Low regeneration temperature
  • Intense cooling
  • No compressed air consumption
  • Regeneration without purging air
  • Pressure build up on the wet side
  • dew point controller
  • Switching without tip in the dew point
  • Safe pressure dew points down to -70°C
  • function messages
  • Alternative energies z. As steam or hot water
  • Various options for optimal adaptability to the needs of the customer
Hochdruckadsorber
Hersteller: Zander
Zander HDK-MT
  • Adsorption dryer high pressure
  • Ecodry HDK-MT 100 and 350 bar
  • high-quality piston valves from mass production combined in one block, individually interchangeable, with separate function for:
  • Adsorption
  • Regeneration
  • Pressure build-up
  • Connection of the valve combinations with the adsorbers to a compact unit
  • Both sides releasable closure of the container
  • Self-cleaning drainage system in the lower inlet area of the adsorber
  • The high-quality desiccant is fixed by an effective bias in the adsorber
Downloads
Aktivkohleadsorber
Hersteller: Zander
Zander AKM
The AKM range of activated carbon adsorbers are designed to purify pre-dried industrial compressed air down to a remaining oil content of 0,003 mg/m³. The units are compact and can be installed either free-standing or on a fram (AKM10-95) or wall mounted (AKM1-8). They come equipped with integrated high performance after filtration and are capable of volume flows up to 940 m³/h in a system operating at 7 barg (100 psig).

Features
Volume flows up to 86 m³/h @ 7 barg (100 psig)
High performance after filters installed as standard
Start-up devices available as an option
Oil indicator installed

Benefits
High performance oil vapour removal for highest quality air
Compact and space saving
Installed high performance after-filter protects downstream equipment

Operation
Pre-dried compressed air flows from top to bottom through a single aluminium profile chamber containing activated carbon. Any remaining oil aerosols and oil vapours including odours and tastes are removed by the active surface area of the highly porous activated carbon to produce high quality, clean compressed air. Finally, the treated compressed air exits via the validated after-filter into the downstream compressed air network. Using an oil-indicator tube, quality checks can be carried out periodically.

Sizing and Selection
Important Note: For quoted air purity performance, compressed air filters must be sized correctly for minimum operating pressure and maximum inlet flow rate using the correction factors found in the Product Information Sheet.

Please note: The lifetime of the activated carbon filling can vary and is dependent on the contamination type and quantity and also on the humidity of the compressed air.

For more information or a detailed discussion about your specific requirements please contact pure!
Downloads
Aktivkohleadsorber
Hersteller: Zander
Zander AK
The AK 120-600 range of activated carbon adsorbers are designed to purify pre-dried industrial compressed air down to a remaining oil content of 0,003mg/m³. The units can be installed free-standing or on a frame. They come equipped with oil indicator and pressure gauge and are capable of volume flows up to 6100 m³/h in a system operating at 7 barg (100 psig). Matching pre- and after-filters have to be ordered separately.

Features
Volume flows up to 6100 m³/h @ 7 barg (100 psig)
Maximum operating pressure 10 barg (145 psig)
Oil indicator, pressure gauge and after-filter included

Operation
Pre-dried compressed air flows from top to bottom through a single vessel containing activated carbon. Any remaining oil aerosols and oil vapours including odours and tastes are removed by the active surface area of the highly porous activated carbon to produce high quality, clean compressed air. Using an oil-indicator tube, quality checks can be carried out periodically.

Sizing and Selection
Important Note: For quoted air purity performance, compressed air filters must be sized correctly for minimum operating pressure and maximum inlet flow rate using the correction factors found in the Product Information Sheet.

Please note: The lifetime of the activated carbon filling can vary and is dependent on the contamination type and quantity and also on the humidity of the compressed air.

For more information or a detailed discussion about your specific requirements please contact pure!
Kartuschenadsorber
Hersteller: Zander
Zander MDK
  • Point of use dryer MDK series (KTM)
  • Pressure dew point -40°C
  • Controllable by test indicator
  • No energy consumption during operation
  • Cartridge system
  • Filling with molecular sieve 4A
  • The filter with cartridge insert absorbs water vapor from compressed air and nitrogen
  • compressed gas for pressure dew points down to -40°C
  • Regenerable by heating
Downloads
Adsorptionstrockner Kaltregeneration
Hersteller: Zander
Zander K-MT - Generation 3
​Fully automatic heatless regenerating adsorption dryer
Volume flow from 8 m³/h to 940 m³/h
Efficient up to a pressure dew point of -70 ° C
Ready to connect adsorption dryer including prefilter and dustfilter 
Optionally available with mounted dew point control
Multitronic plus control
Pressure dew point from -25°C to -70°C
Ready to use adsorption dryer for a pressure dew point of
Standard -40°C.
Higher capacities and operating pressures, inlet temperatures or lower pressure dew points on request.
Downloads

Hersteller: Zander
Zander BSP-MT
  • Efficient processing units for industrial and medical breathing air
  • Flow rates 8 m³/h to 850 m³/h
  • 16 model sizes
  • Lifetime warranty
  • Pressure dew points down to -40°C
  • Exceeds international guidelines e.g. DIN3188, PHARMACOPÉE EUROPÉENNE, EN12021
  • Lowers operating costs
  • Variable control
  • Optionally with load-dependent control
  • Compressor synchronization control possible

Hochdruckfilter
Hersteller: Zander
High Pressure Filter -Series G - 25 up to 50 bar
  • High pressure filter 25 to 50 bar
  • Volume flow 188 m³/h to 2787 m³/h
  • Thread connection G 1/2 to G 11/2
  • Proven Zander G series
  • Ready-to-use filter with manual drain valve
  • Optionally available without drain (drain open, not ready for operation).
Downloads
Hersteller: Zander
Baureihe ausgelaufen
Zander FL Flanged Filter
  • Submicron filter with flange connection for large flow rates
  • Flow rates from 2232 m³ h to 31248 m³/h
  • Flange connection from DN 80 to DN 300
  • Standard range up to 16 bar g (232 psi g)
  • Coalescence filter validated according to ISO 12500-1
  • The resulting air quality complies with all versions of ISO 8573-1
  • The performance has been verified by the independent testing laboratory Lloyds Register
  • Design according to ASME VIII Div 1 (non-U)
  • Reliable separation of solids, oil and water aerosols and oil vapors
  • Increased machine utilization and productivity due to less downtime, less maintenance costs
  • Quick and easy maintenance thanks to NT Easy-Fit element insert
  • Constant low differential pressures throughout the life of the element with high dirt holding capacity thanks to pleated element design
  • Optimal price-performance ratio of operating and wearing parts costs
  • Guaranteed compressed air quality in compliance with maintenance recommendations
  • Stainless steel versions also available
Filterelemente
Hersteller: Zander
Filter elements for Zander G series
  • Advanced Technology
  • Pleated design
  • Paint compatible versions
  • High-temperature version
  • Cartridge versions for activated carbon
  • Five degrees of separation

Kondensatableiter
Hersteller: Zander
Zander ED3000 condensate drain
  • Electronic condensate drain for compressed air and normal condensates up to 16 bar
  • Fully automatic, magnetically level-controlled
  • Supply voltage 230 V, 50-60 Hz
  • Potential-free fault signaling contact as standard (except ED3002, ED3004)
  • Protection class IP65
  • Wear-free magnetic core level control for optimum and lossless drainage of condensate.
  • Integrated strainer between level measurement and diverter valve to protect the diaphragm valve with continuous alarm monitoring.
  • Large diaphragm valve with condensate pilot control for a long service life.
  • Potential-free alarm contact (exception ED3002, ED3004).
Downloads